AIR-AP1810W-T-K9
AIR-AP1810W-T-K9 Обзор
- 1 × Management console port (RJ-45)
- 3 × 10/100/1000BASE-T ports (local Ethernet ports), including 1 PoE out port
- 1 × passive pass-through port RJ-45 (back to bottom)
- 1 × DC power connector
Maximal ratio combining (MRC)
20-, 40- and 80-MHz channels
PHY data rates up to 866.7 Mbps (80 MHz on 5 GHz)
Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Rx)
802.11 Dynamic Frequency Selection (DFS)
Cyclic shift diversity (CSD) support
- 2.412 to 2.462 GHz; 11 channels
- 5.280 to 5.320 GHz; 3 channels
- 5.500 to 5.700 GHz; 8 channels
(excludes 5.600 to 5.640 GHz)
- 5.745 to 5.825 GHz; 5 channels
- 256 MB flash
- 1.4 GHz system dual-core CPU
Figure 1 shows the 360° appearance of the AIR-AP1810W.
Figure 2 shows the face and left side of AP.
Note:
① |
The Face of AP |
③ |
48V DC power port |
② |
The Left side of AP |
④ |
Kensington lock slot |
Figure 3 shows the base of the AP with the ports and connectors.
Note:
① |
Console port |
④ |
LAN port 2 |
② |
Passive Pass-Through port |
⑤ |
PSE / LAN port 1 |
③ |
LAN port 3 |
· PSE / LAN port 1 provides 802.3af/at Power Sourcing Equipment (PSE) PoE-Out power on the LAN 1 Ethernet interface. With 802.3at input the PoE-Out is 6.95W (Class 2).With DC input the PoE-Out is 12.95W (Class 0).
Table 2. Cisco Aironet 1810W series access points can be mounted directly on the wall, to numerous global wall junction standards, or on a desk.
Type of Mounting |
Mounting Bracket or Kit to be Used |
Wall-mount installation on a single gang junction box or multiple international standards. |
AIR-AP-BRACKET-W2 This bracket is shipped with the access point as standard. A spare can also be ordered from Cisco. |
Wall-mount installation directly on wall, where standard junction boxes are not available. |
AIR-AP1810W-KIT= spacer kit This is kit includes an RJ-45 jumper cable and is separately available from Cisco. |
Table-mount installation. See Figure 4. |
AIR-OEAP1810-CRD= cradle kit This is kit includes a back cover, RJ-45 jumper cable and is separately available from Cisco. |
☆ AIR-AP1810W includes a Wall Mounting bracket ( AIR-AP-BRACKET-W2) and has a number of Accessory options which are sold separately and can be ordered as spares.
Figure 4. Table-mount installation.
Note:
① |
The AP |
② |
AIR-OEAP1810-CRD= cradle kit |
③ |
Mounting the AP in the Cradle |
· Cisco Aironet AP1810W series access points can be mounted on a table or horizontal surface, using the AIR-OEAP1810-CRD= cradle kit. This kit is shipped with the access point as standard and includes a back cover and an RJ-45 jumper cable. It is also separately available from Cisco as a spare.
AIR-AP1810W-T-K9 Specification |
|
Authentication and security |
|
Software |
|
Maximum clients |
|
802.11ac |
|
Ethernet ports |
|
Bluetooth (future availability) |
|
Integrated antennas |
|
Interfaces |
◦ PoE out provides 802.3af when access point is powered by Cisco local power supply (AIR-PWR-C=, AIR-PWR-D=), or ~6.5W when powered by 802.3at, or no output when powered by 802.3af
|
Indicators |
|
Dimensions (W x L x H) |
|
Weight |
|
Environmental |
|
System |
|
Input power requirements |
|
Powering options |
|
Power draw |
Note: When deployed using PoE, the power draw numbers listed above include the power loss in 100m of cabling on the uplink port and 100m of cabling on the PoE out port. |
Physical security |
|
Mounting |
◦ AIR-AP1810W-KIT=, spacer kit to mount the access point directly on a wall where standard junction boxes are not available ◦ AIR-OEAP1810-CRD=, cradle kit to mount the access point on a desk |
Accessories |
|
Warranty |
Limited Lifetime Hardware Warranty |